Specifications

USB:   USB 2.0 Full speed, USB 1.1 compatible

Power consumption:  USB – less than 100mA, Power supply – max.1.8A at +13.8V (max. +16V)

CAT:     RxD, TxD – max. 57600 Baud, RTS fixed level output max.1mA
            Levels: TTL, inverted TTL, open collector bus, RS232

Serial:    RS232 levels, RTS fixed level output max.1mA, up to 9600 baud

PA CI-V:   open collector bus max.40mA, up to 9600 baud

All relay outputs:  30VDC, 48VAC, max.2A

External PORT A power:   max. +24V/1.3A

External PORT B power:   max. +24V/400mA

PS/2 consumption:   max. 200mA at +5V

Rotator analog input:  10K ohm, max. +/-12V

Rotator pulse input:   active when grounded,  max. +24V/5mA

Rotator reference output:  9V, max. 20mA

PA Keying output:   open collector, max.+45V/800mA

PA Keying input:   active when grounded,  max.+24V/5mA

PA ON/OFF control:   +12V, max.100mA

Dimensions:    W 305mm (12") x H 90mm (3.54") x D 132mm (5.20")

Weight:    1.8 kg (4 lbs)

1. STATUS LEDs

   POWER

   LED lights when +13.8V is applied (power switch on).

   ALARM

   LED lights when “ALARM” condition happens, transmission may be inhibited.

   BUSY

   LED lights when “BUSY” condition happens, transmission is inhibited.

   LED flashes when “BUSY” condition happens, transmission is allowed.

   READY

   LED lights when transmission is allowed.

   LED flashes when transmit condition has been changed and will be applied on next transmission cycle.

   uLINK

   LED lights when uLINK interface is powered from uLINK HUB.

2. FUNC/MENU

   Short press and release opens “Function” list.

   Press and hold for more than one second opens “Menu” list.

3. Antenna selection nr. 1

4. Antenna selection nr. 2

5. Antenna selection nr. 3

6. Antenna selection nr. 4

7. Antenna selection nr. 5

8. Antenna selection nr. 6

9. Antenna selection nr. 7/NEXT

   Antenna selection nr. 7. If there are more than 7 selections this button moves to next page of antenna selections
   
   

10. RX1-RX2-TX/RX SPLIT

    A short press moves between antenna selections for the RX1, RX2 and TX paths
    Press and hold for more than one second toggles RX1/RX2 receive antennas split “RX SPLIT” RX SPLIT is indicated by small 1 or 2 number on left side of focus mark
    
    

11. [1] Antenna sub-selection nr. 1
    
    

12. [2] Antenna sub-selection nr. 2
    
    

13. [3] Antenna sub-selection nr. 3
    
    

14. [4] Antenna sub-selection nr. 4
    
    

15. MB1, MB2, MB3

    Short press and release recalls memory bank 1, 2, or 3 settings.

    Press and hold for more than one second stores current settings to memory bank 1, 2 or 3.
    Each memory bank is band-dependent.

16. ENCODER

    Rotary encoder with push button. Functions vary based on configuration and antenna selection.

17. <-/YES

    Button for browsing backward among available antennas and menu navigation.

18. ->/NO

    Button for browsing forward among available antennas and menu navigation.
    
    

19. PATH/TX SPLIT

    Short press invokes selected PATH properties menu if exist.

    Press and hold for more than one second toggles RX/TX antennas split, “TX SPLIT”.
    TX SPLIT enabled is indicated by yellow led above button.